24 Results
RTB/RTM/RTA – Measurement result implausible after channel switching RTB, RTM, RTA, measurement result I do RMS measurement on a signal after switching the channels. Even with *OPC? or *WAI the result is implausible: 9.91e+37 . How can I get a correct result? RTB/RTM/RTA – Measurement result implausible after channel switching RTB, RTM, RTA, measurement result I do RMS measurement on a signal after
Delta Time Accuracy Calculation for my Oscilloscope FAQ, Oscilloscopes, RTM, RTA, RTB, Delta Time Accuracy Calculation for my Oscilloscope Delta Time Accuracy Calculation for my Oscilloscope FAQ, Oscilloscopes, RTM, RTA, RTB, Delta Time Accuracy Calculation for my Oscilloscope Related Products
Oscilloscope shows overlayed waveforms FAQ, RTB, RTM, RT, Waveform display, Oscilloscope, overlayed waveform I use the oscilloscope in RUN continious mode. When I press "STOP" more than one acquisitions are shown. The waveforms are overlayed. Is there a way to prevent this? Oscilloscope shows overlayed waveforms FAQ, RTB, RTM, RT, Waveform display, Oscilloscope, overlayed waveform I use the oscilloscope
RTB / RTM / RTA Rackmount kit RTB, RTM, RTA, Rackmount kit ZZA-RTB2K I want to install the RTB / RTM / RTA into a rack and I use the rackmount kit "ZZA-RTB2K". Is the ground of the oscilloscope then connected to the frame of the rack? RTB / RTM / RTA Rackmount kit RTB, RTM, RTA, Rackmount kit ZZA-RTB2K I want to install the RTB / RTM / RTA into a rack and I use the rackmount kit "ZZA-RTB2K". Is the
Change the input impedance with SCPI commands Input impedance, 50 Ohm, 1 MOhm, SCPI command How can I switch between the input impedance of 50 Ohm and 1 MOhm by using SCPI command. Change the input impedance with SCPI commands Input impedance, 50 Ohm, 1 MOhm, SCPI command How can I switch between the input impedance of 50 Ohm and 1 MOhm by using SCPI command. Related Products
LabView Driver rsrtx - Range of Configure Trigger Channel Level RTB2000, RTM3000, RTA4000, Configure Trigger Level, FAQ, LabView Driver LabView Driver rsrtx - Range of Configure Trigger Channel Level LabView Driver rsrtx - Range of Configure Trigger Channel Level RTB2000, RTM3000, RTA4000, Configure Trigger Level, FAQ, LabView Driver LabView Driver rsrtx - Range of Configure Trigger Channel Level Related
No synchronisation in Auto Trigger Mode RTC, RTB, RTM, RTA, HMO, Trigger No synchronisation in Auto Trigger Mode No synchronisation in Auto Trigger Mode RTC, RTB, RTM, RTA, HMO, Trigger No synchronisation in Auto Trigger Mode Related Products
Programming examples for oscilloscopes Programming examples, oscilloscopes, RTH, RTC, RTC1000, RTB, RTB2000, RTM, RTM3000, RTA, RTA4000, RTE, RTE1000, RTO, RTO1000, RTO2000, RTO6, RTP Programming examples for oscilloscopes. Programming examples for oscilloscopes Programming examples, oscilloscopes, RTH, RTC, RTC1000, RTB, RTB2000, RTM, RTM3000, RTA, RTA4000, RTE, RTE1000, RTO, RTO1000, RTO2000, RTO6
RTB/RTM/RTA: Other units than V or A at channels? RTB, TRM, RTA, RTB/RTM/RTA: Other units than V or A at channels? RTB, TRM, RTA, Related Products
Measurement of the voltage of a waveform at a certain time Measurement of voltage, waveform at certain time, captured waveform, SCPI commands I would like to measure the voltage at a certain time of a captured waveform. Do I need to use the cursor function? May I ask for the SCPI commands? Measurement of the voltage of a waveform at a certain time Measurement of voltage, waveform at certain time, captured
RTB/RTM/RTA - reduce Stop Frequency at FFT RTB/RTM/RTA - reduce Stop Frequency at FFT RTB/RTM/RTA - reduce Stop Frequency at FFT RTB/RTM/RTA - reduce Stop Frequency at FFT RTB/RTM/RTA - reduce Stop Frequency at FFT RTB/RTM/RTA - reduce Stop Frequency at FFT Related Products
SCPI command for Average + HR Mode SCPI command, average + HR Mode, I want to set the acquisition mode to Average + HR using SCPI commands. But I can not find the right command in the manual. SCPI command for Average + HR Mode SCPI command, average + HR Mode, I want to set the acquisition mode to Average + HR using SCPI commands. But I can not find the right command in the manual. Related Products
Calibration certificate? Calibration certificate; ZNL; ZNLE; FTP1000; RTH1000; RTB2000; ZPH; FPH; FPC1000; RTM3000 Calibration certificate? Calibration certificate; ZNL; ZNLE; FTP1000; RTH1000; RTB2000; ZPH; FPH; FPC1000; RTM3000 Related Products
Output frequency of the Arbitrary Generator is wrong? RTB, RTM, RTA, output frequency, arbitrary generator When I set the frequency of the arbitrary generator to 10 KHz, the frequency of the output signal is 120 KHz. What is wrong here? Output frequency of the Arbitrary Generator is wrong? RTB, RTM, RTA, output frequency, arbitrary generator When I set the frequency of the arbitrary generator to 10
RTM / RTA Remote commands for manual burst of the generator RTM-B6, RTA-B6, manual burst I am using the burst function of the function generator. But I can not find the remote command to set the burst to "manual". RTM / RTA Remote commands for manual burst of the generator RTM-B6, RTA-B6, manual burst I am using the burst function of the function generator. But I can not find the remote command to
RTB / RTM / RTA - changing the timebase with active FFT RTB, RTM, RTA, FFT With active FFT it seems that the timebase setting can not be changed. Is there a way to do that? RTB / RTM / RTA - changing the timebase with active FFT RTB, RTM, RTA, FFT With active FFT it seems that the timebase setting can not be changed. Is there a way to do that? Related Products
RTB/RTM/RTA Screenshots on the internal memory RTB, RTM, RTA, Screenshot I have saved some important screenshots in /INT/SCREEN path. Now I want to save/copy these data on a USB key or my PC. RTB/RTM/RTA Screenshots on the internal memory RTB, RTM, RTA, Screenshot I have saved some important screenshots in /INT/SCREEN path. Now I want to save/copy these data on a USB key or my PC. Related Products
Configuring the Probe Adapter RT-Z2T with remote commands RTM, RTA, RT-Z2T, probe adapter Configuring the Probe Adapter RT-Z2T with remote commands Configuring the Probe Adapter RT-Z2T with remote commands RTM, RTA, RT-Z2T, probe adapter Configuring the Probe Adapter RT-Z2T with remote commands Related Products
How can I copy the screen shots from the internal memory to an USB stick? Oscilloscope, RTM3000, RTA4000 How can I copy the screen shots from the internal memory to an USB stick? How can I copy the screen shots from the internal memory to an USB stick? Oscilloscope, RTM3000, RTA4000 How can I copy the screen shots from the internal memory to an USB stick? Related Products
RTB/RTM/RTA/RTH - Remote Display function with Instrument View Software RTB/RTM/RTA/RTH, Remote Display function with Instrument View Software I want to use the "Remote Display" function of the Instrument View software. Instead of the screen I just see a "white" area. My PC is connected via USB. How can I use it? RTB/RTM/RTA/RTH - Remote Display function with Instrument View Software RTB/RTM/RTA/RTH
RTM/RTA: Measurement on several pulses of a train RTM, RTA, measurement, pulses of a train RTM/RTA: Measurement on several pulses of a train. RTM/RTA: Measurement on several pulses of a train RTM, RTA, measurement, pulses of a train RTM/RTA: Measurement on several pulses of a train. Related Products
RT-ZSxx – more noise with active probes? Probes, reduce noise, RTM, RTA, RTE, RTO, RTP, RT-ZSxx I have compared passive and active probes. It seems that the noise with active probes is higher. What is the reason and what can I do to reduce the noise? RT-ZSxx – more noise with active probes? Probes, reduce noise, RTM, RTA, RTE, RTO, RTP, RT-ZSxx I have compared passive and active probes. It seems that
Saving a screenshot to an USB stick with remote commands Oscilloscope, HMO, RTC, RTB, RTM, RTA, HMO, RTC1000, RTB2000, RTM3000, RTA4000 Saving a screenshot to an USB stick with remote commands Saving a screenshot to an USB stick with remote commands Oscilloscope, HMO, RTC, RTB, RTM, RTA, HMO, RTC1000, RTB2000, RTM3000, RTA4000 Saving a screenshot to an USB stick with remote commands Related Products
What is the calculation base for the sample rate on my R&S RTA / RTM series scope when using FFT? What is the calculation base for the sample rate on my R&S RTA / RTM series scope when using FFT? What is the calculation base for the sample rate on my R&S RTA / RTM series scope when using FFT? What is the calculation base for the sample rate on my R&S RTA / RTM series scope when using FFT? Related Products