Rohde & Schwarz oscilloscope software

Rohde & Schwarz Oscilloscope software

Select from a wide range of application options for powerful debugging and enhanced analysis

Expand the analysis capabilities of your oscilloscope with application options for protocol-based triggering and decoding, automated compliance tests for the most popular interface standards, general analysis such as jitter or power, or vector signal analysis.

Trigger & Decode Packages
Product Name
Min. bandwidth
Description
Min. bandwidth
50 / 50 / 500 MHz
Description
Trigger & decoding of ARINC 429/ MIL-1553 / SpaceWire data & communication buses. 
Min. bandwidth
600 MHz
Description
Triggering and decoding of 100BASE-T1/BroadR-Reach® and 1000BASE-T1 Automotive Ethernet
Min. bandwidth
50 MHz
Description
T&D package for automotive protocols such as CAN, CAN-FD, CAN-XL, LIN, FlexRay, SENT, CXPI
Min. bandwidth
600 MHz
Description
8b10b, Manchester and NRZ
Min. bandwidth
600 MHz
Description
Decoding software 10Base-T, 100Base-Tx and MDIO
Min. bandwidth
600 MHz
Description
Serial triggering and decoding: I2C/SPI/ RS-232/UART/I2S/LJ/ RJ/TDM/Manchester/NRZ
Min. bandwidth
4 GHz
Description
D-PHY ( DSI, CSI-2), M-PHY / UniPro
Min. bandwidth
1 GHz
Description
MIPI RFFE 
Min. bandwidth
6 GHz
Description
8b 10b, PCI Express 1.1/2.0/3.0
Min. bandwidth
2 GHz
Description
USB 1.1 / 2.0 / 3.2 Gen1/2 / HSIC/SSIC / Power Delivery (PD)
Serial triggering and decoding
Product Name
Min. bandwidth
Description
Min. bandwidth
-
Description
Bus measurement for serial protocol decoding
Min. bandwidth
600 MHz
Description
Triggering and decoding of 100BASE-T1/BroadR-Reach® and 1000BASE-T1 Automotive Ethernet
Min. bandwidth
600 MHz
Description
Universal decoding of 8b10b buses
Min. bandwidth
50 MHz
Description
Triggering and decoding of ARINC 429 buses
Min. bandwidth
50 MHz
Description
Triggering and decoding of CAN and LIN interfaces
Min. bandwidth
50 MHz
Description
Triggering and decoding of CAN-FD
Min. bandwidth
50 MHz
Description
Triggering and decoding of clock extension peripheral interface (CXPI) buses in line with SAE J3076
Min. bandwidth
600 MHz
Description
Decoding of 10BASE-T and 100BASE-TX Ethernet
Min. bandwidth
50 MHz
Description
Triggering and decoding of FlexRay™ buses
Min. bandwidth
50 MHz
Description
Triggering and decoding of I²C and 2-wire, 3-wire or 4-wire SPI buses
Min. bandwidth
50 MHz
Description
Triggering and decoding of I²S buses
Min. bandwidth
200 MHz
Description
Triggering and decoding of any Manchester and NRZ coded serial protocol such as Profibus PA, DALI, MVB and many proprietary protocols
Min. bandwidth
200 MHz
Description
Triggering and decoding of MDIO
Min. bandwidth
50 MHz
Description
Triggering and decoding of MIL-STD-1553 buses
Min. bandwidth
4 GHz
Description
Triggering and decoding of the MIPI D-PHY based protocols DSI and CSI-2
Min. bandwidth
4 GHz
Description
Triggering and decoding of the MIPI M-PHY physical layer and the UniPro protocol layer
Min. bandwidth
1 GHz
Description
Triggering and decoding of the MIPI RFFE-protocol
Min. bandwidth
6 GHz
Description
Triggering and decoding of PCI Express Gen 1.1, 2.0 and 3.0 signals
Min. bandwidth
50 MHz
Description
Triggering and decoding of UART based protocols and RS-232, RS-422 and RS-485 buses
Min. bandwidth
50 MHz
Description
Triggering and decoding of fast channel and short and enhanced serial messages. Meets SENT SAE J2716 v2010 and legacy standard.
Min. bandwidth
500 MHz
Description
Triggering and decoding of SpaceWire data and communications buses.
Min. bandwidth
2 GHz
Description
Triggering and decoding of all USB 1.x/2.0 data rates: high speed (480 Mbit/s), full speed (12 Mbit/s) and low speed (1.5 Mbit/s)
Min. bandwidth
13 GHz
Description
Triggering and decoding of USB 3.1 Gen 1 and Gen 2 signals
Min. bandwidth
1 GHz
Description
Triggering and decoding of USB power delivery (USB-PD) signals
Min. bandwidth
2 GHz
Description
Triggering and decoding of USB-SSIC signals
Compliance test
Product Name
Min. bandwidth
Description
Min. bandwidth
600 MHz
Description
Automated compliance test solution for 10/100/1000BASE-T Ethernet interfaces according to the IEEE test specification
Min. bandwidth
600 MHz
Description
Automated compliance test solution for 10/100/1000BASE-T Ethernet interfaces according to the IEEE test specification
Min. bandwidth
1 GHz
Description
Automated compliance test solution for 2.5G/5GBASE-T Ethernet interfaces in line with IEEE test specification
Min. bandwidth
3 GHz
Description
Automated compliance test solution for 10GBASE-T Ethernet interfaces according to the IEEE test specification.
Min. bandwidth
4 GHz
Min. bandwidth
600 MHz
Description
Automated compliance test solution for 10BASE-T1S and 10BASE-T1L Ethernet in line with IEEE 802.3cg specification
Min. bandwidth
600 MHz
Description
Automated compliance test solution for 100BASE-T1/BroadR-Reach® Ethernet in line with openSIG compliance test specifications
Min. bandwidth
2 GHz
Description
1000BASE-T1 Ethernet compliance test solution in line with IEEE 802.3bp specification
Min. bandwidth
2 GHz
Description
Automated compliance test solutions for DDR3, DDR4 and DDR5
Min. bandwidth
1 GHz
Description
Automated compliance test solution for eMMC interfaces in line with JEDEC specification JESD84-B51 version 5.1, covering HS200 and HS400 bus speed modes
Min. bandwidth
4 GHz
Description
Automated compliance test solution for HDMI interfaces in line with HDMI forum 1.4b/2.1 (TMDS) test specifications
Min. bandwidth
4 MHz
Description
Automated compliance test solution for R&S®MIPI D-PHY in line with MIPI and UNH-IOL test specifications
Min. bandwidth
4 GHz
Description
Automated compliance test solution for R&S®MIPI D-PHY in line with MIPI and UNH-IOL test specifications
Min. bandwidth
6 GHz
Description
Automated compliance test solution for PCI Express interfaces (systems and cards) according to PCI-SIG compliance test specifications
Min. bandwidth
2 GHz
Min. bandwidth
-
Description
Fully automatic Ethernet compliance test for 100BASE-T, 100BASE-T1 and 1000BASE-T1 compliance
Min. bandwidth
13 GHz
Description
Automated compliance test solution for DisplayPort 1.4a and embedded DisplayPort 1.4b/1.5 (covering bit rate mode RBR, HBR, HBR2, HBR3)
General analysis
Product Name
Description
Description
Advanced eye analysis of acquired waveforms with 8/16 Gbps configurable HW-CDR
Description
Extends the trigger capabilities of the R&S®Scope Rider handheld oscilloscopes. Additional trigger types such as pattern, state, runt, slew rate, window, data2clock, serial pattern, timeout and interval or TV/video
Description
Clock data recovery of embedded clocks in realtime with the R&S®RTO oscilloscope
Description
Deembedding in realtime for fast results
Description
Frequency counter for R&S®Scope Rider handheld oscilloscopes
Description
The frequency response analysis option uses the built-in oscilloscope waveform generator to create stimulus signals ranging from 10 Hz to 25 MHz on RTx and 0.01 Hz to 100 MHz on the MXO.
Description
Displays up to 64 harmonics with the R&S®Scope Rider handheld oscilloscopes
Description
Increases the vertical resolution of the Rohde & Schwarz oscilloscopes to up to 16 bits
Description
Capture and analyze pulsed and bursted signals over a long period
Description
Analyze high-speed serial signals with the hardware based clock data recovery (CDR) up to 16 Gbps
Description
Jitter Measurements such as cycle-to-cycle jitter or time interval error (TIE); enabling track display
Description
Separation of individual jitter and noise components such as Random, Data Dependent or Periodic components; display of step response, histograms, synthetic eye diagrams, spectrum and BER-bathtub curves
Description
Analysis of switch mode and linear power supply characteristics with automated measurements and wizard support
Description
Enhances the powerful multichannel spectrum analysis capability of Rohde & Schwarz oscilloscopes, incl. spectrogram
Description
Trigger on user-defined zones. Zones can be applied to channels, math and FFT signals
Description
Enables measurements on signals up to PAM-8 order.
Description
Embedding (up to 5 components) and Equalization (TX-FFE, CTLE, FEE, DFE)
Vector signal analysis
Product Name
Description
Description
Converts modulated signals to I/Q data for further processing
Description
The R&S®VSE vector signal explorer software brings the experience and power of Rohde & Schwarz signal analysis to the oscilloscope, offering a wide range of analysis options for troubleshooting and optimizing your designs
Description
Integrated setup control for external R&S®FExx frontends
Analysis / Remote control software
Product Name
Description
Description
R&S®InstrumentView remote analysis for Rohde & Schwarz oscilloscopes: Download waveforms from your oscilloscope to your computer and use this software to analyze them in detail.
Description
The R&S®CDS campus dashboard software simplifies teaching of student groups in laboratories with multiple workbenches.
Description
Enables the R&S®Scope Rider's integrated wireless LAN module, allowing easy remote control of the  R&S®Scope Rider.
Description
Enables the control of the R&S®Scope Rider touch interface and keypad through the web browser of any notebook or tablet.(requires R&S®RTH-K200 or R&S®RTH-K200US option).
    0 of 3 Compare products
    Select at least 2 Products

    Request information

    Do you have questions or need additional information? Simply fill out this form and we will get right back to you.

    Marketing permission

    Your request has been sent successfully. We will contact you shortly.
    An error is occurred, please try it again later.
    General and legal information

    Manufacturer's recommended retail price (MSRP). The price shown does not include VAT. Prices and offers are only intended for entrepreneurs and not for private end consumers.

    You may use the electronic signature via DocuSign to submit your information to enroll with the Rohde & Schwarz Customer Delegated Administration program. DocuSign processes the information provided according to their . The minimum system requirements for using the DocuSign system may change over time. The current system requirements are found

    Terms & Conditions of the Prize Draw 10 years Rohde & Schwarz oscilloscopes

    1. The prize draw “10 years Rohde & Schwarz oscilloscopes” (herein referred to as “Draw”) is organized by Rohde & Schwarz GmbH & Co. KG, Mühldorfstraße 15, 81671 Munich, Germany, Tel. +49 89 41 29 0 (herein referred to as “R&S).

    2. All participators can register to the draw during January 01, 2020 to December 31, 2020 with their name, company name and business e-mail.

    3. Participation is free of charge and not dependent on the purchase of goods or services.

    4. The draw is only open to legal entities and only the legal entities are able to win the prizes. An individual person is not allowed to participate on its own name and its own account but as a representative of a legal entity filing the participation form in the name of and on behalf of the legal entity.

    5. The prizes to win are 1 of 10 R&S®RTB2000 within the time frame January 1, 2020 to December 31, 2020:

    Prize: 1x R&S®RTB2000 Digital Oscilloscope

    6. The draw takes place at Rohde & Schwarz headquarters, Muehldorstrasse 15, 81671 Munich. The winner of the prizes will be informed by e-mail within 5 (5) working days.

    7. The authorized representative of the legal entity shall inform Rohde & Schwarz about the acceptance of the price. In case of the denial of the acceptance, or no answer within two (2) weeks, a new winner will be drawn. If no winner can be determined within four (4) weeks, the draw ends and the prize forfeit.

    8. R&S’ employees and members of their families and also person being familiar with the process of the draw and members of their families are excluded from filling the participation form.

    9. No cash equivalent or exchange of prizes is allowed. Prizes are non-transferable. All taxes, levies, duties, fees and other charges levied in the participant´s country shall be borne by the participant.

    10. Personal data will be processed only for the purpose of this prize draw and deleted four (4) weeks after the draw, if not agreed otherwise.

    11. Any Participant who does not comply with these Terms & Conditions may be disqualified by R&S from this Competition. In such cases, prizes can also be withdrawn retrospectively. In case a prize is withdrawn retrospectively due to the non-compliance with these Terms & Conditions, it shall be returned by the respective participant at his cost to R&S’ address mentioned under Nr.1 and a new winner will be drawn.

    12. The participants cannot claim the prizes of this draw and no legal recourse is permitted in this respect.

    13. The draw and any contractual relationship arising therefrom between R&S and the respective participant shall be governed by and construed in accordance with the laws of Germany, without any recourse to the conflict of laws. The courts of Munich, Germany, shall have exclusive jurisdiction in case of any disputes arising directly or indirectly from the participation in this Competition.

    * “fast delivery” inside 7 working days applies to the Rohde & Schwarz in-house procedures from order processing through to available ex-factory to ship.